P0300: Random or multiple cylinder misfire detected

What the code tells you on its own

System
Powertrain

Engine, fuel, air, ignition, emissions and transmission. The overwhelming majority of what workshops bring to the AI.

Functional group
Misfire
Subsystem
Ignition system or misfire
Failure type byte, when the tool sends one
00 (No sub-type information)

Scan tools report the same fault as P0300 and as P0300xx, where xx is a sub-type. They are one fault, and whether the sub-type appears at all depends on the tool and the protocol rather than on the car.

Diagnostics

What we see when P0300 turns up

Measured across the diagnostics run through Wrenchlane, not taken from a reference table. Figures as of 2026-10-06.

Diagnostics
44

February 2026 to October 2026

Separate workshops
37

Not one shop meeting it repeatedly

Arrived code only
9%

No symptom description entered at all

Most common marque
BMW

Where we have seen it most

These are counts from our own work, not a claim about how common the fault is across all vehicles. They describe what independent workshops brought to us, which is a narrower and more specific thing.

Our diagnosis data

What WrenchLane ranked first on P0300

Across 33 real diagnoses of P0300 from 26 workshops (February 2026 to November 2026), this is the cause WrenchLane ranked most likely for the code, grouped by the part it named. Most often: Ignition coil, in 24% of them.

  1. Ignition coil 24% (8 of 33)
  2. Vacuum or intake air leak 15% (5 of 33)
  3. Spark plug 12% (4 of 33)
  4. Engine mechanical wear (compression, valves, gaskets) 6% (2 of 33)
  5. Fuel injector 6% (2 of 33)
  6. Other causes 36% (12 of 33)

Makes we see it on most: Audi 4 · Chevrolet 3 · Volkswagen 3 (of 33)

Codes that came in with P0300

Code What it is Same diagnosis
P0301 Cylinder 1 misfire detected 7 of 33 (21%)
P0303 Cylinder 3 misfire detected 7 of 33 (21%)
P0171 System too lean, bank 1 6 of 33 (18%)
P0302 Cylinder 2 misfire detected 4 of 33 (12%)
P0304 Cylinder 4 misfire detected 3 of 33 (9%)
P0420 Catalyst system efficiency below threshold, bank 1 3 of 33 (9%)

How to read this: these are the causes WrenchLane ranked first from the codes, the car and what the mechanic entered, not confirmed repairs. Each diagnosis is anonymised: no workshop, customer or number plate is used. Our own test accounts, the demo car and repeat runs of the same car are left out. We only publish a figure that rests on at least 10 diagnoses from at least 3 different workshops, with no single workshop above half of them; a code listed alongside needs at least 3. It describes what independent workshops brought to us, not how common a fault is across all cars. Data as of 2026-11-17. How we use diagnosis data

FAQ

Frequently asked questions

How do I run a diagnosis?

Select the vehicle on Start, click the Diagnostic card and choose New diagnostic. Fill in the description, the error codes and the mileage, then click Analyze.

Copy link
Do I have to type the codes from my scan tool?

No. Click the camera button next to Error codes and take or choose a photo of the scan tool's screen; WrenchLane reads the codes and their descriptions into the form. You can also speak them with the microphone.

Copy link
Are the public fault code pages built from my diagnostics?

They use diagnostics run in WrenchLane, with no workshop, customer, registration number or VIN shown. Each fault code page shows how often the code was seen and in how many workshops.

Copy link

Run P0300 against the car in front of you

Enter the code and the symptoms and get ranked probable causes for that specific vehicle, with the checks in the order worth doing them.