Turbo, boost & air intake

Diagnosing P1592 on a 2008 Audi A6 2.0 TDI

See how to diagnose a P1592 boost pressure correlation code on a 2008 Audi A6 2.0 TDI. Learn why the ECU, wiring, and sensors all play a part in the failure.

P1592

2008 Audi A6 /-Allroad (4F)

P1592 on a 2008 Audi A6 /-Allroad: Defective or drifted boost pressure sensor (G31) Watch the 60-second Short →
In this article

A 2008 Audi A6 2.0 TDI arrived with code P1592 for a boost pressure signal fault, immediately limiting fuel before the engine even started. The Bosch EDC16U31/U34 engine control unit runs a key-on, engine-off (KOEO) test comparing the G31 boost pressure sensor to the internal F96 atmospheric pressure sensor, and this vehicle failed that initial check.

Wiring resistance and ground faults

Our diagnostic platform ranked wiring resistance as the most probable cause for this specific fault. According to TPI 2015624/2, the factory harness on this 2.0 TDI engine (BRE) is prone to micro-corrosion at the pins and oxidation at the chassis ground points. The G31 sensor relies on an analog signal referenced to ground.

An increase in resistance of just a few ohms on the ground line creates a voltage drop of 100 to 250 millivolts. The ECU reads this as a false boost pressure, such as 1180 mbar instead of a realistic 1000 mbar. If the discrepancy exceeds the 30 to 50 mbar factory tolerance, the ECU logs P1592 and triggers the glow plug light. The correct test here is reading measuring block group 010 with the ignition on, then measuring the voltage drop on the G31 ground wire against the negative battery terminal.

Sensor drift and internal electrical failures

The second highest probability was an internal failure or measurement drift inside the G31 sensor itself. This piezoresistive component operates under constant pressure pulsations and vibrations. Over time, the strain gauge structure can suffer material fatigue, causing a calibration offset.

A healthy sensor supplied with a 5.0V reference should return a voltage between 1.60 and 1.90V at an atmospheric pressure of 1000 mbar. If it shifts to 2.20V or 1.30V, the EDC16 unit sees a mismatch against its internal barometer. Technicians should verify the 5.0V reference on pin 3, then use a hand vacuum and pressure pump to test the linearity of the sensor signal.

ECU water ingress and the F96 sensor

We also see cases where the G31 sensor is perfectly fine, but the internal F96 atmospheric sensor is reporting skewed data. In the Audi A6 (4F) platform, the F96 sensor is soldered directly to the ECU motherboard. The ECU sits in the E-box located in the plenum chamber.

Leaves and debris routinely block the rubber water drains in this area. During heavy rain or washing, water floods the E-box and breaches the ECU enclosure. This causes electrolytic corrosion on the 94-pin connector or the F96 sensor itself, locking the reported atmospheric pressure at a false value like 800 mbar. A visual inspection of the plenum drains and the T94 connector for moisture is a necessary diagnostic step.

Sensor fouling from soot and oil

The final confirmed failure mode involves physical blockage. The 2.0 TDI BRE engine routes crankcase vapors and EGR soot through the intake system, creating a thick, sticky layer of carbon and oil sludge. The G31 sensor has a very small measuring port leading to its diaphragm.

When this port becomes restricted, it can trap residual boost pressure. After shutting off the engine, the trapped pressure bleeds away too slowly. On the next key cycle, the sensor reports an artificially high value. Removing the sensor to inspect the measuring port and cleaning it with isopropyl alcohol will confirm or eliminate this cause.

Next steps for a P1592 diagnosis

Start this diagnosis without turning the engine over. Connect a scan tool, turn the ignition on, and monitor measuring block 010. Compare the atmospheric pressure from the ECU against the intake manifold pressure. If they differ by more than 50 mbar, measure the G31 ground circuit voltage drop before replacing any parts.

Topics

Start diagnosing with confidence today

Try WrenchLane and see how much time you can save, from diagnosis to repair.