Turbo, boost & air intake

Diagnosing P0113 on the Audi A4 Allroad 3.0 TDI

Learn how to diagnose a P0113 fault code on a 2009 Audi A4 Allroad 3.0 TDI, from G31 and G42 combined sensor failures to wiring harness breaks.

P0113

2009 Audi A4 Allroad (8K) III

In this article

A 2009 Audi A4 Allroad rolls into the bay with an illuminated check engine light and a single P0113 fault code stored in the Bosch EDC17 control unit. Our diagnostic platform recently analyzed this exact scenario, mapping out a clear path through the shared sensor circuits of the 3.0 TDI CCWA engine.

The combined G31 and G42 sensor architecture

On the 3.0 TDI CCWA engine, the intake air temperature sensor (G42) is integrated directly into the boost pressure sensor (G31). This combined unit sits on the pressure pipe after the charge air cooler and before the throttle valve. The temperature sensor uses an NTC thermistor element. When the air temperature rises, the electrical resistance drops.

Our data ranked an internal break in this thermistor element as the most likely cause, at 45 percent probability. Thermal cycling and intense engine vibrations eventually fracture the internal connections. When the thermistor breaks, the circuit opens completely. The engine control unit sends out a 5-volt reference voltage. Without the thermistor to pull this voltage down to ground, the control unit measures nearly 5.0 volts. The system interprets this as an extreme cold reading of -40 degrees Celsius and immediately triggers the P0113 code for a high input circuit.

To verify this, technicians should read the intake air temperature in the measuring blocks with both a cold and warm engine. A resistance measurement directly on the NTC pins at a known temperature will confirm an open circuit.

Connector fretting and oil contamination

If the sensor itself tests fine, the next most probable cause is the physical connection. We ranked oxidation, oil contamination, or contact play in the sensor connector at a 30 percent probability.

The connector lives in a harsh environment. It absorbs heavy vibrations from the V6 diesel block, along with radiant heat from the cooling system. Over time, the terminal sleeves lose their spring tension through fretting corrosion. Oil mist from the charge air system can also push past the connector seals, forming an insulating film on the pins. Because the NTC signal is a high-resistance circuit, even a microscopic break or slight contact resistance forces the signal voltage above 4.6 volts, which is enough to trigger the P0113 code.

A visual inspection of the terminals with a magnifying glass is a practical starting point. You can also perform a pin drag test to check the clamping force of the terminal sleeves, followed by a wiggle test on the connector while watching live data.

Harness routing and wiring faults

When the sensor and connector are healthy, the fault usually lies further up the wiring harness. We ranked a broken signal or ground wire at a 15 percent probability, and a short circuit to a 5-volt or 12-volt source at 6 percent.

The signal and sensor ground wires travel from the G31/G42 unit across the engine bay to the J623 engine control unit in the plenum chamber. The harness bends sharply around engine lifting eyes and passes close to the radiator and charge air pipe brackets. Millions of vibration cycles can snap the wires at these stress points. If the signal or ground wire breaks, the internal pull-up resistor in the control unit forces the signal to 5.0 volts.

Similarly, if the harness rubs against the chassis, the signal wire can short directly to the adjacent 5-volt supply for the boost pressure sensor. This permanently forces the signal to maximum voltage, regardless of the actual temperature.

Where to start your diagnosis

When diagnosing a P0113 on this 3.0 TDI engine, always start by checking the live data for a default -40 degree Celsius reading. Your first physical check should be the connector at the G31/G42 sensor on the charge pipe. Perform a quick pin drag test to rule out fretting corrosion before replacing the combined sensor unit or stripping back the main engine harness.

Reference pages for the codes in this article

  • P0113: what we measure for this code across real diagnostics

Start diagnosing with confidence today

Try WrenchLane and see how much time you can save, from diagnosis to repair.