Engine & misfires Hybrid & electric

Peugeot 508 Hybrid4: Diagnosing Intermittent Starts

How to diagnose intermittent starting issues and multiple fault codes on a 2011 Peugeot 508 Hybrid4 2.0 HDi using shared power supply testing.

P0001 · P0003 +3

2011 Peugeot 508 (W2)

In this article

A 2011 Peugeot 508 Hybrid4 arrived in the bay with intermittent starting issues and a hybrid system that refused to enter the READY state. Sometimes the internal combustion engine failed to start completely, while other times it started and then stalled. The engine control unit logged a string of fault codes: P0001, P0003, P0215, P0245, and P2141.

Seeing five separate circuit faults appear simultaneously on a 2.0 HDi engine (DW10CTED4) with Delphi DCM 3.5 injection strongly suggests a shared electrical feed has failed, rather than five separate components failing at once.

Tracing the Common Power Supply in the BSM

Our diagnostic platform ranked a failure of the main relay integrated into the BSM (Boîtier de Servitude Moteur) as the most likely cause, at 82 percent probability. Fault code P0215 directly flags a malfunction of this main engine control relay.

This relay provides the switched +12V supply to a shared branch of engine actuators. This branch powers the fuel flow solenoid on the high-pressure pump (which triggers P0001 and P0003 when voltage drops), the turbo proportional control solenoid (triggering P0245), and the air or EGR throttle (triggering P2141).

If the internal contacts of the relay are oxidized, or if cold solder joints in the BSM cause intermittent voltage drops, the ECU detects an open circuit and low voltage across all three components. Because the fuel flow regulator loses power, rail pressure cannot reach the 250 bar minimum required for starting. The ECU cuts the injection command, and the hybrid control unit prevents the vehicle from entering the READY state for safety reasons.

Inspecting the Engine Wiring Harness for Abrasion

A short to ground on the common actuator harness ranked as the second most likely cause, at 76 percent probability. On the DW10CTED4 engine, the main wiring harness routes through areas highly exposed to vibration. It passes under the air filter housing, near the battery tray, and close to the metal lifting eye on the cylinder head.

If the insulation wears through and the +12V feed or the PWM control lines touch the engine block, the voltage drops to zero. This triggers the circuit low codes for the actuators and induces an overload that forces the BSM relay to disconnect to protect itself, which logs P0215.

Ruling Out the Fuel Regulators and Solenoids

An internal component short can also drag down a shared power circuit. An internal failure of the fuel volume regulator (VCV) ranked at 45 percent probability. This Delphi component mounts directly on the DFP3 or DFP6 high-pressure pump. If the coil shorts internally, it pulls the shared +12V line down, stalling the diesel engine and disabling the hybrid system.

Similarly, an electrical short in the turbo pressure solenoid ranked at 32 percent probability. This solenoid shares the exact same switched supply from the BSM. An internal winding short to ground here will crash the voltage on the entire protected branch.

Prioritizing the First Diagnostic Steps

When presented with these codes on this specific Peugeot powertrain, start by checking the power supply at the source. Perform a voltage drop test on the +12V output line from the BSM to the actuators while cranking the engine. Check the BSM connectors visually for water ingress or oxidized pins, and use DiagBox live data to monitor the main relay status and the voltage measured by the ECU. If the power supply from the BSM holds steady under load, proceed to measure the insulation resistance to ground on the actuator harness to rule out wire abrasion.

Reference pages for the codes in this article

  • P0001: what we measure for this code across real diagnostics
  • P0003: what we measure for this code across real diagnostics
  • P0215: what we measure for this code across real diagnostics
  • P0245: what we measure for this code across real diagnostics
  • P2141: what we measure for this code across real diagnostics

Start diagnosing with confidence today

Try WrenchLane and see how much time you can save, from diagnosis to repair.